sheet resistance

This instrument has been used for measuring the sheet resistance distribution for Boron diffusion chip.

并用该仪器测定了硼扩散片的薄层电阻分布.

This instrument has been used to measure the sheet resistance distribution for Boron diffusion chip.

并用该仪器测定了硼扩散片的薄层电阻分布。

The results showed that the remaining adhesive on the surface of the steel sheet increases the film resistance, and consequently the total contact resistance between steel sheets rises.

研究结果显示，预压后残留于钢板表面的胶粘剂形成的胶层膜电阻会使得钢板间接触电阻增大。

For the as-deposited films, the sheet resistance is of inverse proportion function as the sputtering time.

溅射态合金薄膜方块电阻与溅射时间呈反比；

The purpose of characterized sheet resistance mapping graph study is to make it clear of the sheet resistance distribution, and increase the analysis effect of test results.

表征薄层电阻的Mapping图的研究目的在于使薄层电阻分布情况一目了然，提高对测试结果的分析效果。

Then, the effects of heat treatment and temperature on the chemical composition and sheet resistance of the prepared films were investigated by XRD, EDXS and sheet resistance measurements.

利用X射线衍射和能量散射X射线能谱表征方法，并结合薄膜方块电阻的测定，探讨了热处理方式和热处理温度对薄膜化学组成及薄膜电阻的影响。

Results show that the TCR of VOx films was increased, and the sheet resistance was reduced effectively both by Mo-doping and W-doping.

结果表明，Mo原子和W原子掺杂均可有效地降低氧化钒薄膜室温方阻，并且提高薄膜的室温TCR。

Research on denting resistance testing for auto body sheet steel

汽车钢板抗凹性试验研究

The results show that electrode degradation mechanism was basically caused by wear due to fracture of local welding between the electrode tip surface and zinc coated sheet steel happen at electrode surface and alloying between electrode and zinc on zinc coated steel during resistance spot welding zinc coated steel.

结果表明：点焊镀锌钢板时电极的失效机制主要是电极和镀锌板之间局部焊接的断裂发生在电极表面而导致的电极磨损以及电极和镀锌板表面的锌之间的合金化。

Resistance spot welding is one of the main connection technology for aluminum alloy thin sheet.

电阻点焊是铝合金薄板主要连接技术之一。

The sheet resistance of antimony-doped tin dioxide thin film coated on soda-lime glass with SiO_2-coated is lower than that of without SiO-coating at the same heat treatment condition.

在热处理温度相同时，预先镀有SiO2膜的玻璃基片上制备的锑掺杂二氧化锡（ATO）薄膜的方块电阻较没有镀SiO2的小。

The sheet resistance of the films can be controlled by changing doping amount of F ions and choosing favorite process conditions, the minimum is 10 Ω/ □.

通过改变掺杂量和选择合适的工艺条件可控制掺氟SnO2薄膜的方块电阻，其最小方块电阻值达10Ω/□。

Pb-free and Cr ( IV)-free prepainted steel sheet with excellent corrosion resistance, formability and weldability is the development direction of automotive fuel tank steel sheet.

具有优良耐蚀性、成形性和焊接性的无Pb、无Cr（VI）预涂层钢板已成为汽车燃油箱钢板发展的方向。

Because the tin-plating thick of 1.0/ 1.0 g/ m~ 2 low tin steel sheet ( LTS) is very thin, the use of LTS is usually affected by decrease of corrosion resistance.

1.0/1.0g/m2低锡量镀锡板镀锡层薄，其使用常常因耐蚀性降低而受到影响。

Monitor of Ion Implantation in IC Process by Contour Map of Sheet Resistance

IC离子注入工艺的薄层电阻等值图监控

The sheet resistance, TVIL and color of ITO films depend on the film thickness.

ITO膜的方阻 、 TVIL和颜色与膜厚有着密切的关系.

"Test method for sheet resistance of silicon epitaxial, diffused and ion-implanted layers using a collinear four-probe array"

GB/T14141-1993硅处延层、扩散层和离子注入层薄层电阻的测定直排四探针法

ITO films with low sheet resistance can be obtained by raising the substrate temperature during deposition or annealing in the inert gases at high temperature.

低电阻率的ITO膜可以通过提高沉积时的衬底温度或高温退火来获得。

The choice of non-ferrous metal low resistance corrugated sheet, Stainless RS corona sheet and corresponding anti-corrosion measures can resist dew-fell and rustiness.

选用非金属低阻波纹板、不锈钢RS电晕板，以及采取相应的防腐措施，能抗结露，耐锈蚀。